PerformaSil® 200

Water-Based Silicone Anti-Graffiti Coating
Protective Ingenuity for Urban Spaces Against Graffiti
Order Samples

PerformaSil® 200 is a Water-Based Silicone Anti-Graffiti Coating

PerformaSil® 200 is your solution for combating graffiti and vandalism. This advanced water-based coating forms a protective barrier on surfaces, allowing for easy graffiti removal without damaging the underlying material. Ideal for public spaces and high-traffic areas, PerformaSil® 200 ensures that your surfaces remain clean and inviting, significantly reducing maintenance costs and efforts.

Features & Benefits

Long-term and non-sacrificial graffiti resistance

Long-term and non-sacrificial graffiti resistance

Easy removal of spray paints, markers, and pens

Easy removal of spray paints, markers, and pens

One-component silicone water-based elastomer

One-component silicone water-based elastomer

Does not yellow, chalk, or fade

Does not yellow, chalk, or fade

Can eliminate repainting costs and prevent properties from losing value

Can eliminate repainting costs and prevent properties from losing value

Ultra-low VOC's

Ultra-low VOC's

Glass Colors

Product Applications

Graffiti Removal

PERFORMASIL® 200 Anti-Graffiti Protected Surface Gets Tagged
Graffiti Removal Image 1
Graffiti Is Easily Removed With Cold-Water Pressure Washer
Graffiti Removal Image 2

Remove graffiti with a power washer (maximum 2000 psi) and cold water. For difficult removal, use warm to hot water while power washing. For delicate surfaces, use a soft bristle brush, soap, and water. Gently scrub the area until the tagging is removed. Rinse the surface with water afterwards. For more difficult graffiti, a commercially available graffiti cleaner may be required. Follow the manufacturer’s recommendations and use instructions.

Surface Preparation and Application

Prior to application all surfaces shall be structurally sound, clean, and dry, free from oils, dirt, debris, or minerals such as efflorescence, lime, and calcium. To ensure the surface is as clean as possible, wash with soap and water, rinse thoroughly, then allow to dry completely. This is especially important when applying over painted, stained, or wood surfaces.

Mix thoroughly before application. Avoid aggressive agitation that may produce excessive air generation or foaming.

Apply using airless spray equipment at a rate of approximately 75 sq ft per gallon (20 mils WFT), using a 0.015 to 0.017 tip. When spraying, apply in a cross hatched pattern to ensure complete coverage of the surface. Rough and/or porous surfaces may require a heavier application to ensure complete coverage. 

Clean application equipment with soap and water when finished.

Application Temperature: 5°C - 38°C (40°F - 100°F)

Relative Humidity: 90% maximum

Graffiti resistance is fully developed after a cure time of 7-14 days. 

Test the product on a small area to ensure finish is satisfactory.

Build American Buy American Image

In accordance with the requirements set forth by the Build America, Buy America (BABA) Act, included within the Infrastructure Investment and Jobs Act (IIJA), we hereby certify and affirm our product, listed below, is manufactured in the United States and meets the criteria defined under the Build America, Buy America (BABA) Act:

PerformaSil® 200 Anti-Graffiti Coating is a polymer-based product entirely manufactured in Washington state and the production process is carried out by a skilled American workforce, adhering strictly to federal, state, and local laws, including labor and environmental standards.

PerformaSil® 200 Bucket

Why install a long-term, non-sacrificial, easy to clean graffiti resistant coating?

Simple, repainting the same graffitied surfaces over and over again isn’t solving the problem, it’s only delaying it.


close

ICD is dedicated to sustainability and the health of our planet.

Discover the PerformaSil® product line of Silicone Water-based Elastomer (SWBE) one-component latexes.

ICD is dedicated to sustainability and the health of our planet.